Repair
هل تريد التفاعل مع هذه المساهمة؟ كل ما عليك هو إنشاء حساب جديد ببضع خطوات أو تسجيل الدخول للمتابعة.

SERVICE MANUAL-SCHEMATIC-Panasonic

اذهب الى الأسفل

SERVICE MANUAL-SCHEMATIC-Panasonic Empty SERVICE MANUAL-SCHEMATIC-Panasonic

مُساهمة من طرف أشرف عثمان الأحد يناير 31, 2016 3:19 am



[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]















[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]










NV-G55

NV-GS11EG

05ree

National Panasonic NV-L15 Video cassette recorder

nv-hp10ram

PANAS_(DL-Mechanizm_Viewcams)

PanasNV112122

PANASONIC

Panasonic NV-MD9000EN Service Manual

PANASONIC NV-SD10,SD20,SD25AM

PANASONIC NV-SD320_SD420

P-RN510AW

RX-6_7[ServoBlock]
أشرف عثمان
أشرف عثمان
Admin
Admin

عدد المساهمات : 716
تاريخ التسجيل : 29/01/2016

https://repair.forumegypt.net

الرجوع الى أعلى الصفحة اذهب الى الأسفل

SERVICE MANUAL-SCHEMATIC-Panasonic Empty رد: SERVICE MANUAL-SCHEMATIC-Panasonic

مُساهمة من طرف أشرف عثمان الأحد يناير 31, 2016 3:20 am



Diagnosis and tuning VCR PANASONIC K-mechanism



Currently, the vast majority of Panasonic VCRs series SD, HD, HS and
video players series HR, SR is based on the K-mechanism has proven its
reliability and durability in operation with relative ease. Appearance
mechanism on the upper side is shown in Fig. 1, bottom - in Fig. 2. In
parentheses are the number of parts needed in their order or purchase.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.1 View of the mechanism on top

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.2 View of the mechanism below

ASSEMBLY MECHANISM
In the process of repair mechanism is often necessary to its partial
disassembly for replacement parts that fail. The article describes the
assembly sequence that part of the mechanism, which ensures proper
phasing of its work, as well as methods of verification mechanism after
assembly.
The assembly is performed in the following sequence:

1. Fits gear due to a mechanism for loading cassettes and fixed split washer (Fig. 1).
2. Fits lever control efforts freezes podkassetnogo receiving node (Fig. 1).
3. Set the lever position P5 and gear drive clamp rollers (Fig. 1).
4. Installed base lock position P5 and fixed split washer and screw (Fig. 1).
5. Fits latch position P5, the bracket with rollers and opener magazine covers.
6. Supporting software installed gear so that the hole in it
coincided with a hole on the chassis of the mechanism, while the second
(small) hole must be matched with a hole in the gear drive pinch roller.
Position of gear can fix a pin that is removed after final assembly
(Fig. 2). Protrusion on the bracket with a pinch roller to be wound into
a groove on the auxiliary program gear.
7. Install the stator engine drive shaft and fix it with three
screws, keeping the alignment holes. After that, install the rotor
motor. On the drive shaft during installation should be dressed in two
glands (one above the other - at the bottom).
8. Installs the gear, rotating the gear connection with the cassette
loading mechanism so that her teeth did not come into engagement with
the gear program. Give birth to a ledge regulator lever effort freezes
podkassetnogo receiving node in the slot program gears (Fig. 2).
9. Set the mode switch by aligning marks on its side and rotating on a fixed frame and fixed with screws.
10. Withdrawn holders with stands filling tapes in the bottom
position, while ensuring that the correct position lever adjustment of
belt tension and fasting P5. Establish a system of levers filling tapes
(Foster and supply), by matching tags (small holes) on the gears.
11. Installs the bar, the plant in its grooves pins regulator lever
belt tension lever and spring tension so that the match marks on the bar
and on the gear receiving node filling system tape (Fig. 4). Perpetuate
the bar three slotted washer.
12. Install the drive gear and mount the engine load.
13. Install the plate with the brake and the roller and belt. Secure
the plate with two screws. With roller adjust the belt tension.
14. Node set to open magazine covers, plant ledge on it in the bracket with a pinch roller.
At the end of the assembly mechanism must ensure the correct phasing as in Fig. 3 and 4.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.3 Phasing sites mechanism, top view


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.4 Phasing sites mechanism, bottom view
After this test the mechanism by turning by hand a worm gear on the
engine load. Applications should avoid excessive force, since in the
case of jamming of the possibility of breakage of some details. At the
end of manual checking is fed to the engine load voltage from the three
series-connected battery (4,5 V), and perform checking mechanism work.
Once the scan return mechanism to its original position.
It should be noted that the above details of the phasing mechanism
corresponds to the position when the cassette is loaded. To install the
assembled cassette translate it into position swapped tapes. Rotate the
engine to manually load in the direction of ejection cartridge, install
the gear due to the loading mechanism in the position shown in Fig. 5.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.5 Phasing loading mechanism in the unloaded state magazine
The position of the label on the movable part of the mode switch must match the one shown in Fig. 6.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.6 The position marks the mode switch in the state unloaded magazine
Install the cassette into the mechanism in accordance with Fig. 5 and attach it with four screws.
It should be noted that when performing unloading cassettes without
cassette should ensure traction tabs on the gear due to the loading
mechanism with a slot in the program gear, turning the hand-gear
connection clockwise.
When assembling the cassette directly on the chassis of the mechanism
of translating it into the position of the loaded cartridge, ensuring
alignment marks on the gear lever of the loading and rail loading
mechanism, as shown in Fig. 7.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.7 phasing mechanism for cassette tape loaded in the state
After that, install the side plate cassette to the chassis so that
the first prong on the rail loading mechanism coincided with the mark on
the gear due to the loading mechanism, as shown in Fig. 8.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.8 phasing gears in status loaded magazine
Reinforce the side plates with four screws, transfer mechanism in the
unloaded position and set the tape cassette holder. Then set the upper
metal panel cassette.

EXTRACTION CARTRIDGES
If as a result of a failure, it is impossible to unload the tape, try to remove it the following methods.

1. Take out mechanism (if possible), and manually rotating the worm
gear, relocating the fueling tape to the bottom position. Rotate the
motor rotor drive shaft counterclockwise podmatyvayut tape. Rotate the
worm gear to unload the tape.
2. Served on the socket engine load voltage from the three
series-connected batteries (plus on pin 2 connector) and relocating the
band filling in the bottom position. Rotate the motor rotor drive shaft,
podmatyvayut tape. Reconnect the battery is discharged cassette.
3. If you remove the tape described method can not perform the following operations:

  • remove the spring, mounted on a bracket with a pinch roller, and lift the bracket;
  • withdrawn position P5 and remove the tape from the racks;
  • rotating motor rotor drive shaft, podmatyvayut tape;
  • remove one screw from the right lateral plate cassette to remove the rail loading mechanism of the connecting gear;
  • turning the hand lever boot, remove the tape.
أشرف عثمان
أشرف عثمان
Admin
Admin

عدد المساهمات : 716
تاريخ التسجيل : 29/01/2016

https://repair.forumegypt.net

الرجوع الى أعلى الصفحة اذهب الى الأسفل

SERVICE MANUAL-SCHEMATIC-Panasonic Empty رد: SERVICE MANUAL-SCHEMATIC-Panasonic

مُساهمة من طرف أشرف عثمان الأحد يناير 31, 2016 3:21 am



COMMON FAULT

Consider the typical failure mechanisms and their causes.

1. Cassette is not loaded or unloaded:

  • broken cassette holder (VXA4661)
  • "Propylene" teeth on the gear lever boot tape (VXP1339);
  • faulty or improperly installed switch mechanism.


2. Tape is not threaded through:

  • faulty braking mechanism podkassetnyh nodes;
  • broken teeth on the drive gear lever filling tapes;
  • program is broken strap.


3. Does not reach the stop lever filling the tape:

  • dirty guide slot chassis or dry lubrication;
  • defective mechanism freezes podkassetnyh nodes.


4. Press down tape:

  • is defective or not configured the ribbon (often Unstick felt strip);
  • dirty or warped pressure roller;
  • bent arm position P5.


5. Tape is not moving in the playback mode:

  • improperly installed or defective drive bracket with the pinch roller;
  • defective central clutch that transmits rotation podkassetnye nodes. 6. Tape is not at podmatyvaetsya raspravke:
  • faulty braking mechanism podkassetnogo receiving node (VXZ0313).


7. Crashes when you change modes:

  • faulty switch mechanism;
  • crack in program bar (in this case usually fails the phasing mechanism.)


8. Shutter does not open when unloading the cassette tape:

  • broken arm opening blinds (VXL2250);
  • broken shutter (VKF2709).


9. Cover will not open the cassette upon startup:

  • broken arm (VML2680), mounted on the cassette holder;
  • broken opener magazine covers (VDM2101).

It should be noted that the reason of incorrect work may be the
mechanism of its contamination or ingestion of foreign objects. In the
latter case, may damage the gears, the program bars and levers.


ADJUSTMENT MECHANISM
The need for mechanical adjustments tape mechanism occurs after
prolonged use, the replacement of any of its parts, as well as due to
unauthorized repairs.

ADJUSTING THE ARM the ribbon

1. Remove the top panel with the cassette and cassette holder.
2. Rotate the engine load to bring the mechanism to the position filled by the tape.
3. With the holes in the eccentric holder belt controller belt
tension adjusting the position of the lever. The left edge of the lever
must match the left edge of the clip (see Figure 9)..

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 9 band brake lever position


ADJUSTING THE TENSION BAND

1. Enables playback (mounted on top of the tape length 180 minutes) and give the tape to stabilize (approximately 10 ... 20).
2. Measure belt tension in the area between the head full erase and
fasting P2 (see Fig. 10) with a meter (VFK 0132). Meter reading should
be between 22.5 ... 27.5, the
3. If the belt tension does not fit into these limits, adjust it,
moving the governor spring tension belts on short-or long tooth (in the
original position it is on the average).


PROVISIONAL ADJUSTMENT POSTS P2 and P3


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig. 10 Location of posts

1. Remove the top panel with the cassette and cassette holder.
2. Weaken the fixing screws positions P2 and P3.
3. Rotating positions P2 and P3 in a clockwise direction, set them in the lowest position.
4. Pivoted to positions P2 and P3 2 turns counterclockwise.
5. Set the cassette holder and the top panel cassette.
6. Load the tape and start playback. Verify the absence of knee tape
in the upper and lower floors of the restrictive positions P1, P2, P3,
P4.
7. In the case of bending strip remove him adjusting positions P2 and P3.
8. Setting compatibility BM (substitutability tapes).

To configure the compatibility of the VM should do the following:

1. Adjustment positions P2 and P3;
2. Preliminary adjustment of the block of magnetic heads (BMG) in height;
3. Height adjustment BMG;
4. Precise control of BMG;
5. Adjusting the BMG horizontally. Before you begin, you should
disable the auto-tracking. To this end, the microcontroller is converted
into service mode jumper between control points:

  • TP SERV and TP GND for a series of SD;
  • TP 6010 and TP 6011 series HD.

Voltage at NORM / SERV / TEST MCU in this case is 2,5 ... 4 B. At the end of the jumper settings are removed.
In the models later release disable Auto-tracking can be done
installing the service mode by pressing two buttons, the FF and EJECT.

ADJUSTMENT POSTS P2 and P3

To adjust the tracking set to the middle position while pressing the
TRACKING "+" and "-" button on the remote control (RC) when playing a
standard recording (cassette VFJ8125H3F).
Oscilloscope control signal to the amplifier output signal from the
video heads (RF SIGNAL). To obtain a stable image scan of the
oscilloscope can zasinhronizirovat pulse switch the video heads (HEAD SW
PULSE).

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.11 The shape of the envelope RF-signal (start reading)


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.12 The shape of the envelope RF-signal (end of reading)
If the envelope of the RF-signal at the input tape in contact with
the video heads (when you turn on the video heads) has the form shown in
Fig. 11A or 11B, it is necessary to adjust the position P2 to obtain
the waveform shown in Fig. 11C. If the envelope of the RF-signal at the
output tape from contact with the video heads (when you turn off the
video heads) has the form shown in Fig. 12D or 12E, you should adjust
the position P3 for the waveform shown in Fig. 12F. Adjusting the
tracking in either direction from the central position, you must make
sure that the shape of the envelope corresponds to that shown in Fig.
13.V if necessary, further adjust positions P2 and P3.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.13 The shape of the envelope RF-signal at different positions of adjustment tracking


Pre-installation of unit magnetic heads (BMG)

Rotate the screw A (see Fig. 14) to touch his gear and then turn it to 1.5 turns counter clockwise.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.14 Block stationary heads
Turning the screws B and C, set the database D with respect to the
base E, as shown in Fig. 14. When adjusting the screws B and C are not
allowed to touch the surface with a screwdriver heads.

ADJUSTING THE HEIGHT BMG
In playback mode, rotate the screw A or until the bend ribbon at the
bottom of the post of P4, and then turn the screw in the opposite
direction until the disappearance of knee tape. Attach the oscilloscope
to the output audio channel, and turning the screw C, we achieve maximum
signal. The bottom edge of tape should be above the lower edge of the
magnetic sinhrogolovki BMG approximately 0.25 mm.

EXACT ADJUSTMENT OF THE HEIGHT BMG
If the position of tape does not match the above, then for BMG
lifting screw is rotated a counterclockwise until you bend ribbon at the
bottom of the post of P4. Then turn the screw in clockwise until the
disappearance of the bend the tape, and screw C until the maximum
amplitude of the signal. To lower BMG screws rotate in the same sequence
in a clockwise direction.

ALIGN BMG Horizontal
Set the tracking to the middle position, while pressing the TRACKING
"+" and "-" on the remote while playing a reference recording. Connect
the oscilloscope to the amplifier signal video heads (RF SIGNAL). Weaken
the screws holding the base E BMG to the chassis and turn the base, we
achieve maximum value envelope of the RF-signal.
After that anchoring base E screws.


MODE Self-Test
In video recorders (VTR) provides the function of self-diagnostics,
which provides, in case of malfunction, the displayed information in the
form of a code indicating a fault.
The list of codes is given in Table 1.
CodeThe reasonVerification (correction)
U10The formation of dewWait until it disappears
H01Does not rotate SHIRBRIGCheck the motor control circuit SHIRBRIG
H02No tape in the cassette podmatyvaetsya during raspravki except mode "Eject"Check the control circuit of the drive shaft
F03The mechanism is locked during mode switching, but the regime "Eject"1. Check motor load control circuit
2. Check the phase synchronization mechanism
3. Check switch
F04Mechanism is blocked during raspravki tape1. Check motor load control circuit
2. Check the phase synchronization mechanism
F05No tape podmatyvaetsya during raspravki mode "Eject"1. Check the control circuit engine drive shaft
2. Check the operation of sensor nodes podkatushechnyh rotation (the presence of pulses)
F06Mechanism is blocked after raspravki tape mode "Eject"1. Check motor load control circuit
2. Check the phase synchronization cassette
F07Supply voltage record does not show up in record modeCheck the power supply circuit for the circuit record
F08Supply voltage recording appears, except the recording modeCheck the power supply circuit for the circuit record
F09No transfer of a clock signal between the microcontroller and the chip timerCheck the path passing the clock signal

Table 1: Error codes


SERVICE MODE

Service mode allows you to verify the operation of various units of
VM. In this case, the display shows information in the form of
facilities and rooms service mode data service, which allows to detect
faults and, thus, reduce the repair time.
Entry into service mode by simultaneously pressing the "FF" and
"Eject" (or turning the handle to position "FF" and click "Eject") on
the front panel of the VM. Switching service modes implemented in the
same way.
The display shows information in the form of four (or five) digits.
The first digit (a digit hour display) indicates which of the seven
service modes the machine. The second and third digits (digits in
minutes) - this service data indicating a position to verify the scheme
or mechanism. The fourth (or fourth and fifth - 01, 02, etc.) figure (in
the discharge of seconds) - is the number of service data that
indicates in any scheme to be a problem.
Customer information is not dependent on service conditions and
stored in memory after you turn off the VM from the network. Deriving
this information to the display is carried out in service mode 2.
Consider the appointment of service modes.

Mode 1
Checks the tape protection schemes, ie Work
emitting diode and photodetectors beginning and end of the tape by
blocking the radiation on the photocell.
Mode 2
Checks the circuit switch modes in the transition
mechanism from one position to another with an indication of the
mechanism in the form of service data.
Mode 3
Checks the circuit switch mode after completion of the transition mechanism from one position to another.
Mode 4
Checks of the control buttons on the display should
appear on the index (in the ranks of service data), corresponding to
each of the buttons.
Mode 5
Calibrated work of motor control circuit of the drive shaft, ie, transmission of commands from the microcontroller (MC).
Mode 6
Inspects the work of the motor control circuit SHIRBRIG.
Mode 7
Checks of the engine load. When the button is
pressed "Play", the engine load is rotated in the direction of loading.
When the button is pressed "Stop", the motor rotates in the direction of
discharge. This mode can be indicated by an unlimited time with power.
Non-service data in various modes and their meanings are given in Table
2. Non-service information and their values ​​are given in Table 3.
Room service modeNote: to check the package service dataCodes of service dataValueNotes
100Radiation were found at both photodetectorsThe tape is not required
01Blocked by radiation at the photodetector end of the tape (left)
02Blocked by radiation at the photodetector beginning of the tape (right)
03Radiation is fed into both the photodetector
200Cassette is unloadedRequires tape
1 Stop-3: The pressure roller is pressed against the drive shaft
2 Stop: pinch roller is spaced from the drive shaft.
To check the status of the mechanism and timing see Fig. 1
01The cassette is loaded
02Rev, Rev Slow
03Filling, raspravka tape (middle position)
04Play / Rec, Still / Pause, Cue, Fwd Slow, Stop-31
05Stop2
06FF / Rew
07Intermediate position
3During the transition mechanism from one position to another service data are not controlled00Any indication, other than "00" at the end of the operation means a fault in the circuit switching mode or systemRequires tape
4Indication of number of service data only when the button is pressedThe tape is not required
5Controlled only by the left-hand figure81Indication 8, 9, U, A, -, n, L, and the lack of
indication means that the MC had received information about passing
command "Play"
Requires tape. If the display shows other than those indicated in the list, it means the failure of the scheme
Controlled only by the right-hand figure87Display of 1, 2, 3, 4, 6, 7 marks the command "Cue", "FF", "Fwd Slow"
Controlled only by the right-hand figure8AIndication 8, 9, U, A, -, n, L, and the lack of indication marks the commands "Rev", "Rew", "Rev Slow"
6Controlled only by the left-hand figure10Display of 1, 3, 5, 7, 9, A, and nothing is displayed on the passing of the command rotation of the engine SHIRBRIG

Table 2 The value of codes of service data
Notes:
1. In some models, the VM no code "U10", "F07" and "F08".
2. Code "U10" is displayed only when the power is.
3. When the lights code "F" or "H" powered the VM is automatically turned off. When power display fault code disappears.
4. Fault code stored in memory and microprocessor timer is stored in
it when disconnected from the VM network. If you repeat Mr. include
trouble code (in the form of one or two digits in the discharge of
seconds) can be displayed by moving the VM to service mode 2. If you
have any new fault in the memory is stored only by its code.
5. To erase the DTC from the memory to simultaneously push the buttons "FF" and "Eject" for 5 seconds.
CodeServiceInformationFault
0 (00)All right
1 (01)Stop cylinder
2 (02)Stop tape reels
3 (03)Stop, except for positions 4 or 6
4 (04)Stop during raspravki tape
5 (05)Abnormal rotation of the drive shaft
6 (06)Stop during loading or unloading tapes
7 (07)Error in the circuit supplying power to the circuit record in writing
8 (08)Error in the circuit supplying power to the circuit record is not in record mode
9 (09)Error in the transmission of clock pulses between the microcontroller and timer

Table 3 The value of codes of service information

ELECTRICAL ADJUSTMENTS

Depending on the VM, the list of adjustable parameters can be
changed. For electrical adjustment requires the following hardware:

  • dual-trace oscilloscope with a frequency range up to 35 MHz;
  • frequency with a frequency range up to 10 MHz, with the ability to measure the period;
  • digital voltmeter;
  • Generator video sweep signal (video scan);
  • generator of sinusoidal signals;
  • video generator;
  • Measuring videofonogramma VFV8125H3F (PAL), VFM8080HQFP (NTSC);
  • net tape VHS;
  • monitor (TV);
  • DC power supply.


It should be noted that, depending on the model of the VM, the list
of adjustable parameters may vary considerably. Depending on the
location of the adjustment elements may vary their item numbers. May
also differ and the conditions under which carried out one or another
regulation.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.15 Timing diagram mode switch


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.16 Adjustment of switching moment heads (PG-SHIFT)


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.17 video sweep signal


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.18 The waveform when adjusting the frequency response videochannel


[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
Fig.19 Waveform priregulirovke Identification System SECAM
In view of the foregoing, it is not possible in this article to
describe all the possible options for electric adjustments, so we will
focus on the most common of them. Electrical adjustment procedures are
presented as Table 4.
أشرف عثمان
أشرف عثمان
Admin
Admin

عدد المساهمات : 716
تاريخ التسجيل : 29/01/2016

https://repair.forumegypt.net

الرجوع الى أعلى الصفحة اذهب الى الأسفل

SERVICE MANUAL-SCHEMATIC-Panasonic Empty رد: SERVICE MANUAL-SCHEMATIC-Panasonic

مُساهمة من طرف أشرف عثمان الأحد يناير 31, 2016 3:22 am



G-Mechanism VCR PANASONIC



With what can be compared to assembling G-mechanism? More
all, with the assembly of three-dimensional puzzle, only
error will be noticed immediately, but after switching
VCR. This article will help you
Part Number identify the defective part, and after
replace it quickly and correctly assemble the mechanism.
There are three modifications of G-mechanism:
proper G, G-REV and GII, have small
structural differences, but performed by a single
kinematics. Such a mechanism
manned video recorders (VTR) Panasonic
Series G, H, J, L, etc., as well as some other VMs
firms (in particular, Grundig).
Due to relatively high consumer
qualities, VCR with G-mechanism are in
operation for quite a long
time. In this regard, coming into repair VM
often require the replacement of worn or
broken parts of the kinematics and its subsequent
adjustment, which causes some
difficulties due to the complexity of the mechanism.
In this paper we consider the kinematic
scheme of the mechanism and the assembly sequence of the
part of it, which requires phasing.
KINEMATIC PATTERN MECHANISM


On Fig. 1 shows a view from below
G-REV-mechanism.
Fig. Figure 2 shows the kinematic scheme
bottom, and Fig. 3 - upper part of this
mechanism. The diagram shows the relationship and
phasing of the details of the mechanism for the mode STOP.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Fig. 2. Kinematic diagram of the lower
part of the mechanism

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Fig. 3. Kinematic diagram of the upper
part of the mechanism
Feature of the mechanism is that
loading cassettes and change regimes mechanism
carried out from the engine drive shaft (in the GII-mechanism
part of the operations carried out additional
engine). Rotation from the engine through
central sleeve and a leading disc is transferred to the
disc clutch. With this disc rotation
transmitted to the central and related
separator and ring gears. Separator
gear transmits rotation to the main
Soft pinion gear and software
filling the tape. The main program gear
a pinch roller drive gear
the moving of the drive mechanism
pinch roller and the mode switch, and
a lever connection - Software straps.
Pinion Software by filling tapes
notched transmits rotation to the gear
filling the tape.
Ring gear transmits rotation to the
Product Wizards gear, and by
it - on the pinion with rack
cassette.
ASSEMBLY and phasing MECHANISM


Consider the assembly sequence
mechanism in a part that requires the phasing.
Incorrect phasing mechanism can lead
its jamming and damage to components, so
after assembly mechanism is recommended that you manually
sweep without a greater effort to
ensure proper functioning.

  • Install the ring gear, combining
    a hole in it with a hole chassis as
    shown in Fig. 4. Then set
    Product Wizards gear, combining
    a hole in it with a hole in the chassis.
    In this case, a small hole must be
    opposite the holes in the ring gear. After
    This set the lock lever.
    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 4. Install the ring gear
  • Install the upper side of the chassis
    gear drive pinch roller. Then
    establish a core program gear
    so that the small holes on it and on
    pinch roller drive gear were
    on one line. A large hole in the software
    gear should be in this match with a hole
    in the auxiliary program gear, as
    shown in Fig. 5.>

    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 5. Setting up basic program
    Gear
  • Installs the gear fueling
    tape so that the protrusion auxiliary lever
    Filling tape was combined with the groove (A) in it, as
    shown in Fig. 6. Rotate the gear so
    to a small hole in it was on
    in line with the axis of the ring gear as
    shown in Fig. 7. Then set
    separator gear with three planetary
    gear over the ring gear so that
    holes in it were in front of the holes in the
    Key Policy gear filling the tape. In
    Meanwhile, the hole in the separator gear
    should coincide with the opening in the ring
    gear, as shown in Fig. 8.
    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 6. Installing the gear
    Filling tape
    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 7. Phasing gears
    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 8. Install separator Gear
  • Establish a central gear over
    separator gear, aligning the holes in it
    with a hole in the separator wheel. At the same time
    small hole should be opposite
    holes in the disk clutch, as shown in Fig.
    9. The central gear is fixed to the shaft
    split washer (VMX1079).
    [ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]
    Fig. 9. Installing central gear
أشرف عثمان
أشرف عثمان
Admin
Admin

عدد المساهمات : 716
تاريخ التسجيل : 29/01/2016

https://repair.forumegypt.net

الرجوع الى أعلى الصفحة اذهب الى الأسفل

SERVICE MANUAL-SCHEMATIC-Panasonic Empty رد: SERVICE MANUAL-SCHEMATIC-Panasonic

مُساهمة من طرف أشرف عثمان الأحد يناير 31, 2016 3:22 am



"Seals" for gear




Sometimes repairing tape drives
VCRs, camcorders, copiers and
other equipment, "rests" in a broken tooth
some gears (Fig. 1, sector 1).
Gear, this is either very expensive or her
virtually unobtainable. The author hopes
that the method described below, will be available to many
master repairmen.

[ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة]

Figure 1
For a start, made from paraffin
proofing gear. To do this from the paraffin candles
diameter of 25-40 mm cut cylinder of height 15-20 mm.
Then you need a well heated soldering iron with a thin
melt the wax from the end of the cylinder to 1 / 2
diameter and 1-2 mm deeper than the thickness of the pinion.
Further, in liquid paraffin should put that part of the
Gear that has all the integer teeth.
Addressing a soldering iron melted paraffin to
completely fill the entire space between
teeth. For safety you can drop the top 3.4
a drop of melted paraffin, then
must set aside this construction until
cooling and solidification of paraffin.
Once frozen paraffin, a scalpel or
cutter remove thin layers of its surplus with the
top gear (in Fig. 1, Sector 2 paraffin
visibility is covered with a thin layer of paint). Then
neat, a gentle lurch extract
gear from a paraffin cylinder. If something
did not work (defects in the prints, broke
excavation, etc.), the procedure is repeated until
get an even impression of the teeth.
Now you must prepare itself gear.
To do this, it will be convenient to use
mikrodrelyu for drilling circuit boards or small
drilling machine. Dental burs, already
unsuitable for dental treatment, but it is
suitable for such operations,
You can get it from any dentist. Incidentally, there
You can also purchase and mikroabrazivnye stones and
grinding wheels. A small dental bur
opposite the broken tooth in the body gear
milled notch (Fig. 1, Section 3). Depth
cavity is 2 / 3 or 3 / 4 the thickness of the gear.
Further, a gear must be properly
degrease. You can use the
brush and gasoline "Galoshes" or
solvent grade 646-647. While the gear dries
diluted with epoxy glue in traditional
proportions. His need quite a bit, but
should be very thoroughly mixed composite
part of the glue. Then selects the sharpest
imprint of teeth on the paraffin cylinder and a needle
filled with glue. After you do this as soon as possible
rather invest in gear notch up
imprint. Then embedded into the groove
"Fittings" - a piece of steel needles or
thin the broken drill bit. Desirable region
"Reinforcement" to be laying in the
paraffin imprint obtochit small
abrasive or sandpaper to shape the tooth, so
is, give it a wedge shape. After laying
"Reinforcement" to the edges of the recess is filled with glue and
drown in it short pieces of thin threads (Fig. 1,
Sector 4). Better if it would be Mylar,
kamelanovye or silk thread (they have
high strength). Needs to be monitored,
to thread properly impregnated with glue.
Resulting from the addition of adhesive thread bump
best left alone until the setting point.
After curing the adhesive gear removed from the
wax and needle files to remove the bump side
gears. If turned "litnichki"
between the teeth, they can cut blade
safety razor or nail file
(Diamond).
It remains to add that in this way
recovered a variety of traction,
brackets, hooks and gear the program
vehicles with mechanical logic
أشرف عثمان
أشرف عثمان
Admin
Admin

عدد المساهمات : 716
تاريخ التسجيل : 29/01/2016

https://repair.forumegypt.net

الرجوع الى أعلى الصفحة اذهب الى الأسفل

الرجوع الى أعلى الصفحة

- مواضيع مماثلة

 
صلاحيات هذا المنتدى:
لاتستطيع الرد على المواضيع في هذا المنتدى