TOSHIBA- Service Mode-سرفس

TOSHIBA- Service Mode

---

Chassis S5E, C6S 2050 2150, 1478XR, 1450, 1458, 20N3 2163DB/DD/DF/DN/DS Proc. M3722M6-A80SP/A81SP/B80SP/B84SP
login
1.na remote control (MUTE)
2. Re-press (MUTE) and do not let go
3. Press (MENU) on TV
On TV, where there are no buttons MENU, there is a small hole in front of which the desired button - press the match.
output - POWER OFF

model 2185XR, 29AX9UM
login
Press the button on the remote control (MUTE)
2. Once again, click on the button (MUTE) and do not let it go
3.
Press the TV button (MENU). Each press of a button (CHANNEL UP) changes
adjusting the position of each click on the button (+ VOLUME) and
(-VOLUME) changes the data.
Exit - Turn off the TV or Exit MENU

Model 2512-DD.
login - Simultaneously press the "F" and "AV" on the remote, then enter code 1048.

model 2929DD, 2812DS percent. CXP80424-144
login
Hold down the (F) submit a command with the remote control (AV).
Then, immediately dial (1) (0) (4) ([ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة] When typing on the 1048 figures will appear in white.
After a few seconds you will see in the right corner the letter M. If you press and hold the button (F) button (9) will test.
If you press and hold the button (F) button (2) off the screen but the sound is.
If
you press and hold the button (F) button (Z) will display the settings
options from the perspective of the TV 16 to 43 (need to change the
position by pressing the (z).
Will increase if you make a button (S) positions will be reduced output POWER OFF

Chassis C7SS 28W7D Proc. TMP87CS38N-3477
login - Press the (MUTE) on the remote. Click on it again and holding press (MENU) for TB.
output - POWER OFF

---

TOSHIBA 2185XR.
To enter the service to 1. put pressure on the button (MUTE)
Remote control. 2. Once again lean on the button (MUTE) and do not let go 3. Click on
button (Menu) on TV. Any pressure on the (CHANNEL UP) button position
regulation changes. Any pressure on the buttons (-VOLUME) and
(+ VOLUME) modifies the data. Exit - Turn off the TV.
* * *
TOSHIBA
1.In the pressure on the regime SERVICE apparatus of a button - the line
Horizontal ON / OFF (circle with an arrow). If you have found and clicked, then
any subsequent press changes the picture. 2. In the menu of adjustments
Vol. (9) the occurrence of self-diagnosis menu SELF CHECK. ******** - The number of
CPU Power - 00 - Diagnosis power supply module. 00 - normal,
if other figures show how many times the protection system is reset -
tendency to overload currents. Bus line - control
tire chains. OK-rate, SDA - GND - ks bus to ground SDA, SCL - GND -
same bus SCL. SDA-SCL - naturally with each other. Bus cont -
check tire components. OK - the norm. Q *** NY - chip number
*** Faulty. SYNC - Synchronization. OK - the norm. NG - runs per cent. and
trying to determine the type of video
Exit - click the button POWER.
* * *
2929DD
Hold down the (F) command file from the remote control (AV).
Then just dial (1) (0) (4) ([ندعوك للتسجيل في المنتدى أو التعريف بنفسك لمعاينة هذه الصورة] Exit: POWER OFF.
* * *
TOSHIBA S3E
1Nadavit button on the remote MUTE.
2) Again, click on it though.
3) Hold it, push the menu on the TV.
* * *
TOSHIBA S5E CHASSIS.
1450 XN \ XNE 2050XN 1458XNH 2150 XNE \ XHC \ XC. Enable
self: When displayed on the screen adjustment menu, press the button
9 on the keypad. Start up the process of self-test.
* * *
TOSHIBA S5E CHASSIS 2150.
Input: 1. (Mute); 2. (Press MUTE again or release), 3. (Click on
TV MENU); "4" - correction of the contrast. "1", "2", "3" - cutoff G, R,
B "AV" - Select the tone for the test. "- Volume" - adjustment. Output:
* * *
CHASSIS C6S S5E 2050 1478XR, 2150, 1450, 1458, 20N, 32163DB /
DF / DD / DN / DS
1. (MUTE)
2. again (MUTE) to press and release
3. to press (MENU) on TV
On TV, where there is no MENU button, the front has a small hole in which
desired button - press the match.
Connect the test signal: With the push service => on the remote.
Introduction self-diagnosis: In the Service (9) push the
remote. Self-find a menu there and all is clear.
Memory initialization: In the press service (CHANELL) and (CALL) in
the same time. Exit: POWER OFF
* * *
Chassis - 5N11,
to withdraw from the key, it is necessary to disassemble the remote and carefully glance
by gum, there is a button, without the graphite layer, and a key with them and
shoots. Geographically it is - the second row of buttons below the oval 3 or 4,
button on the left. I do not remember.
* * *
TV TOPSONIC
on LC863332A-5Z51, remote control - 5Z51-902 (CD7461CO on IC), memory - 24CO8.
Entering the service menu: 2-16 feet CD7461CO (the button is hidden). For each
pressure on all around me: FACTORY - then B / W BALANCE-then ADJUST
MENU 0 - TV. Translation ADJUST MENU (0 - 9) Bridging the 3 - 15 pin.
Screensaver changed easily to everyone else, I'm on the "Monitor" changed
(Splash explicitly visible on the side).
* * *
TV URABRAND.mod.dct-1492.
shassis
unknown, "China's assembly," Memory: 24c08, processor
TDA9370PS/N3/A TSG 0430 3, PAL, NTSC 4.43, NTSC3.48-there, SEKAM-no.
The sound in the service activated. Entering the service menu:
"Uncivilized": programmer to prescribe the cell 1D1-FF,
when you connect the device enters the service mode.
Knopkami1 elect-8 menu pages. Exit button I. Memorization
automatically happens. In the absence of the original remote you can use the MAC code 1264